Add-On: GPSI-3900 Inputs

The 3900 device is equipped with four inputs, which can be enabled upon request. To submit a request, contact the Support Team. Additional tools and/or parts that you may need include: razor knife, electrical tape, zip ties, wire crimper, wire stripper, wire cutter, 12V or 24V relay, relay harness, 20ga wire, ground screw, ring terminal,…

Add-On: GPSI-3900 Driver ID

The installation kit contains one iButton Reader, one plastic washer, one metal locking washer, four butt connectors, two key fobs, and one buzzer, or one light. Additional tools and supplies you need include one drill, one 10 mm. drill bit, one 13 mm. drill bit (light), wire strippers, a crimping tool, electrical tape, and zip-ties.…

Unit Verification App

With the GPS Insight Unit Verification App (iOS | Android), you no longer have to call in to verify your installation. The application allows you to quickly verify the installation of the GPS device as well as register the device for immediate viewing within the portal. Before You Begin the Verification Process When you have…

Testing for Battery Drain

Although it may be possible for a device’s power draw to exacerbate existing battery conditions (i.e., an old battery or other after-market products causing draw), the device alone should not cause battery draw issues. If you’re unsure, the following steps will help you test draw: Not in Sleep Mode All testing should be completed when…

GPSI-3900E jPOD

This video walks you through the following steps in the installation on process: Locate the vehicle’s diagnostic port, and ensure proper voltage. Install the external antenna, and route the cables. Free up existing JPort, and install bypass cable. Mount the replacement diagnostic port. – INSTALL OPTIONAL ADD-ONS – Prep the harness, and connect the jPOD…

GPSI-3900 jPOD

Before You Begin The installation kit contains a registration card, the 3900 device, a 20-pin harness, an external antenna, a heavy-duty 9-pin bypass cable, and a jPOD. Additional tools that you may need include a digital multimeter, zip ties, electrical tape, and tamper seal compound. Complete the registration card by locating the serial number of…

GPSI-3900I/E vPOD

This video walks you through the following steps in the installation process: Locate the vehicles OBD-II port, and ensure proper voltage. Free up existing OBD-II port. Assemble mounting bracket, and connect the OBD-II Pass-Thru Cable to the vehicle’s OBD-II port. Mount the replacement OBD-II port, and pull cable through the dash. Install the external antenna,…

GPSI-3900I/E vPOD

Before You Begin The installation kit contains a registration card, the 3900 device, a 20-pin harness, a light-duty OBD-II bypass cable, a vPOD, and an external antenna (if applicable). Additional tools that you may need include a digital multimeter, a crimping tool, a razor knife or wire strippers, a butt connector, zip ties, electrical tape,…

GPSI-3900E

This video walks you through the following steps in the installation on process: Install the external antenna, and route the cable. Locate wires with proper voltage for constant and switch power. Connect the constant, switch, and ground wires. – INSTALL OPTIONAL ADD-ONS – Connect the antenna cables to the device. Tape the harness wires, and…

My GPSI-3900E jPOD Stopped Tracking

Confirm that the vehicle is parked out in the open and is with cellular coverage. From the Manage Vehicles page, ping the unit using the refresh icon  next to the vehicle’s last ‘Reported’ date/time, or contact Tech Support with the unit’s serial number for the initial unit assessment. Ignition Detection Issue This issue may occur…

My GPSI-3900 vPOD Stopped Tracking

Confirm that the vehicle is parked out in the open and is with cellular coverage. From the Manage Vehicles page, ping the unit using the refresh icon  next to the vehicle’s last ‘Reported’ date/time, or contact Tech Support with the unit’s serial number for the initial unit assessment. Ignition Detection Issue This issue may occur…

My GPSI-3900 Stopped Tracking

Confirm that the vehicle is parked out in the open and is with cellular coverage. From the Manage Vehicles page, ping the unit using the refresh icon  next to the vehicle’s last ‘Reported’ date/time, or contact Tech Support with the unit’s serial number for the initial unit assessment. Ignition Detection Issue This issue may occur…

GPSI-3900E

This is our flagship truck tracking device. This device requires a three-wire installation and is typically mounted in the dash for a concealed installation, with only the external antenna visible. The 3900 is highly configurable to support optional features such as Driver ID, Panic Button, Garmin Navigation and Messaging, Power Take-Off Monitoring (must be voltage based),…

GPSI-3900E

Before You Begin The installation kit contains a registration card, installation guide, 3900 device, antenna, 20-pin harness, ring terminal, self-tapping ground screw, star washer, eight 8″ (20 cm) and six 14″ (35.5 cm) zip ties. Additional tools and supplies that you may need include a digital multimeter, crimping tool, razor knife, wire strippers, electrical tape,…