My ST-1200 Stopped Reporting

If the ST-1200 device ever becomes unresponsive, meaning its standard reporting has ceased but you’re certain the unit is charged, then reset the device following the below instructions so that it can restart its programming and resume reporting. This process requires the download and use of the (Orbcomm) Field Support Tool app (iOS|Android). Resetting the…

ST-1200

This battery-powered, asset-tracking device is ideal for trailers, storage containers, or other assets that are not powered regularly. The ST-1200 delivers greater efficiency with the latest in asset tracking technology. Get complete visibility of trailers and containers virtually anywhere in the world, improve asset utilization and driver productivity, streamline operations, expedite cargo delivery and more…

ST-1200

The installation kit contains a registration card, the ST-1200, one abrasive pad, one alcohol wipe, two 3M primer sticks, five rivets, four self-tapping screws, four flanged button head machine screws, four well nuts, a packet of dielectric grease and two spare locknuts. Additional tools and supplies that you may need include a cordless drill, fine…

Is an Outdated Browser Holding You Back?

Make Sure You’re Not Missing Any Features If you’re using Internet Explorer version 10 or older, this is a great time to update your browser so you can get more from your GPS Insight solution. Microsoft has not supported these older browsers since 2016, which means you may be missing out on certain features and…

How Does the ST-1100/ST-1200 Report?

The ST-1100/ST-1200 device uses solar power to charge its battery, and only uses cellular networks to develop and receive data. Since the ST-1100/ST-1200 is mainly solar-powered, its reporting functions are different than your average device. Reporting Motion Reporting The ST-1100/ST-1200 begins reporting once a unit has moved for a complete mile. Once the unit hits…

Unit Verification App

With the GPS Insight Unit Verification App (iOS | Android), you no longer have to call in to verify your installation. The application allows you to quickly verify the installation of the GPS device as well as register the device for immediate viewing within the portal. The screenshots within this guide are specific to the…

Add-On: AT-3000 Inputs

Additional tools you may need include a multi-meter, insulated wire crimper, wire stripper, 12 VDC or 24 VDC weatherproof relay and relay harness, 20ga or larger wire, star washer, self-tapping screw, heat shrinking terminal, in-line fuse holder, diode, heat gun, cable ties, and heat shrink butt connectors. Installation Overview The following steps provide an overview…

TTC-1000

The installation kit contains a registration card, the TTC-1000, four 8mm #10 self-tapping screws, four 8mm bolts, eight washers, four locking nuts, and one activation magnet. Additional tools and supplies you need include a cordless drill and one 8mm drill bit. Complete the registration card by locating the ten-digit serial number (ESN) on the side…

TT-2200

This is a satellite-only, battery-powered asset tracking device is ideal for tracking non-powered equipment located in remote areas with little or no cellular coverage.

Add-On: AT-3000 Temperature Sensor

The installation kit contains one temperature sensor, one p-clamp, two heat shrink butt connectors, two standard butt connectors, two grommets, eight 8 in. (20 cm) cable ties with screw hole, twelve 8 in. (20 cm) cable ties, nine self-tapping screws, and 18 ft. cable extension. Additional tools and parts you may need include electrical tape,…

TT-2200

The installation kit contains a registration card, TT-2200 device, four well nuts, and four socket cap screws. Additional tools and supplies that you may need include a fine-tip marker, cordless drill, 5/16 in. (8 mm) drill bit, Phillips-head screw driver, 7/64 in. (2.78 mm) hex key, and a ladder. Installation Steps The following steps provide…

TT-3000

The installation kit contains a registration card, the TT-3000, and one activation magnet (red tag). Additional tools and supplies you need include one 6/32 T10 Torx security bit or screwdriver and four galvanized, self-tapping, tapered head screws or four galvanized bolts with four washers and locking nuts. Complete the registration card by locating the seven-digit…

TT-1800

The installation kit contains a registration card, the TT-1800, and one activation magnet (red tag). Additional tools and supplies you need include four self-tapping, galvanized, tapered head screws or four galvanized bolts with washers and locking nuts, and one serialized security tag. Complete the registration card by locating the seven-digit serial number on top of…

ST-1100

The installation kit contains a registration card, the ST-1100, three 5/16″ (8mm) self-tapping screws, one abrasive pad, two alcohol wipes, one 3M Primer stick, one plastic nut wrench, and two mounting plates. Additional tools and supplies that you may need include a cordless drill, 1/8″ (3mm) drill bit, 5/16″ (8mm) nut driver drill attachment, silicone,…

AT-3000

Before You Begin The installation kit contains a registration card, the AT-3000 device, eight 8″ zip ties, two 14″ zip ties, one star washer, one self-tapping screw, two heat shrink butt connectors, one ring terminal and two inline fuse holders with 3 amp ATC fuses. Additional tools and supplies that you will need include a…

AT-3000

This externally powered asset tracking device is ideal for heavy equipment, generators, diggers, trailers, and other assets that can act as a power source to the GPS tracking device.