Add-On: GPSI-3900 Driver ID

The installation kit contains one iButton Reader, one plastic washer, one metal locking washer, four butt connectors, two key fobs, and one buzzer, or one light. Additional tools and supplies you need include one drill, one 10 mm. drill bit, one 13 mm. drill bit (light), wire strippers, a crimping tool, electrical tape, and zip-ties.…

TT-3000

The installation kit contains a registration card, the TT-3000, and one activation magnet (red tag). Additional tools and supplies you need include one 6/32 T10 Torx security bit or screwdriver and four galvanized, self-tapping, tapered head screws or four galvanized bolts with four washers and locking nuts. Complete the registration card by locating the seven-digit…

TT-1800

The installation kit contains a registration card, the TT-1800, and one activation magnet (red tag). Additional tools and supplies you need include four self-tapping, galvanized, tapered head screws or four galvanized bolts with washers and locking nuts, and one serialized security tag. Complete the registration card by locating the seven-digit serial number on top of…

ST-1100

The installation kit contains a registration card, the ST-1100, one 5/16th self-tapping screw, one abrasive pad, two alcohol wipes, one 3M Primer stick, one plastic nut wrench, and two mounting plates. Additional tools and supplies that you will need include a cordless drill, 5/16th nut driver drill attachment, silicone, clean rag, and an extension ladder.…

AT-3000

Before You Begin The installation kit contains a registration card, the AT-3000 device, eight 8″ zip ties, two 14″ zip ties, one star washer, one self-tapping screw, two heat shrink butt connectors, one ring terminal and two inline fuse holders with 3 amp ATC fuses. Additional tools and supplies that you will need include a…

GPSI-4000LD vPOD2

Before You Begin The installation kit contains one registration card, the 4000LD device, one 4-pin power harness, one 22-pin I/O harness, one light-duty OBD-II bypass cable, one vPOD2 cable, one external antenna, one butt connector, one ring terminal, one ground screw, and one star washer. Additional tools that you may need include a digital multimeter,…

Unit Verification App

With the GPS Insight Unit Verification App (iOS | Android), you no longer have to call in to verify your installation. The application allows you to quickly verify the installation of the GPS device as well as register the device for immediate viewing within the portal. Before You Begin the Verification Process When you have…

ELD-2000

Before You Begin The ELD-2000 installation kit contains one Android MDT (tablet), one MDT Dock, one ELD Data Cable, one RAM Ball Mount kit (incl. backing plate and applicable hardware), four 2.5 mm. hex screws, and one rubber grommet. Additional tools and supplies that you will need include the GPSI-4000HD kit or GPSI-4000LD kit, a…

GPSI-3900 jPOD

Before You Begin The installation kit contains a registration card, the 3900 device, a 20-pin harness, an external antenna, a heavy-duty 9-pin bypass cable, and a jPOD. Additional tools that you may need include a digital multimeter, zip ties, electrical tape, and tamper seal compound. Complete the registration card by locating the serial number of…

GPSI-3900I/E vPOD

Before You Begin The installation kit contains a registration card, the 3900 device, a 20-pin harness, a light-duty OBD-II bypass cable, a vPOD, and an external antenna (if applicable). Additional tools that you may need include a digital multimeter, a crimping tool, a razor knife or wire strippers, a butt connector, zip ties, electrical tape,…

Add-On: GPSI-3900 Inputs

The 3900 device is equipped with four inputs. Any two of these inputs can be used to monitor additional voltage-based activities in a vehicle. Relay Installation Depending on the vehicle, some PTO-Aware/Switch-Based installations require you to convert the positive 12 VDC (+) output from the vehicle to a ground output (12 VDC [+] relay). Any…

GPSI-3900E

Before You Begin The installation kit contains a registration card, the 3900 device, the antenna, and a 20-pin harness. Additional tools and supplies that you will need include a digital multimeter, a crimping tool, a razor knife, wire strippers, a ring terminal, plastic cable ties, electrical tape, tamper seal compound, self tapping screw, and a…

GPSI-3900I

Before You Begin The installation kit contains a registration card, the 3900 device, and a 20-pin harness. Additional tools and supplies that you will need include a digital multimeter, a crimping tool, a razor knife, wire strippers, a ring terminal, plastic cable ties, electrical tape, tamper seal compound, self tapping screw, and a star washer.…

PNP-3000

Before You Begin The installation kit contains a registration card, the PNP-3000 device, and a light-duty OBD-II bypass cable with mounting bracket (optional). Complete the registration card by locating the serial number of the device (labeled “ESN” or “SN”) and copying it onto the card. When the card is complete, you’re ready to start the installation.…

GPSI-4000HD

Before You Begin The installation kit contains a registration card, the 4000 device, an external antenna, a 4-pin harness, a 22-pin expansion port harness, and a heavy-duty 9-pin bypass cable. (The 4-pin harness and 22-pin expansion port harness are required only for optional add-on features.) Additional tools that you may need include a digital multimeter,…